Harding Series Workbench - Extreme Heavy Duty with Stainless Steel Top

Skip to the beginning of the images gallery

Meet ANSI, BIFMA, DIN and GSA Structural Standards.
20,000#. Capacity (Strong Cold Rolled Steel).
14-gauge Strong Cold Rolled Steel.
3" Square Legs.
2" x 3" Rectangular Frame Tube.
One Bolt Per Leg Assembly.
Factory Assembly Available.
2.5" Thick Laminated Top.
The Top is Reinforced with 1-1/2" Solid Particle Board for Strength.
Stainless Steel Top is Grade 304, 18-gauge with #4 Brushed Finish.
Available 24”, 30”, 36”, 43” Wide or Custom.

Not recommended for food preparation areas.

! The longer the table, the weaker the table. To counter this, our eight foot long benches have 66% more steel in the understructure while ten foot long benches have 207% more steel there. These longer tables, even reinforced to this extent, will show some minor deflection in the center due to gravity.

! BenchPro™ Stainless Steel top benches are designed with solid 1-1/2" thick high density commercial grade particleboard under the Grade 304, #4 finish stainless steel to eliminate the possibility of a heavy load bending the top in the center.

! Do not use these benches in cleanrooms, food or drug preparation areas, but instead, use solid stainless steel top tables available from all kitchen supply companies.

! Processing the tops leave small scratches and discoloration. This is normal for this type industrial material.

Harding Series heavy duty benches come standard with adjustable height glides. Bolt down plates are available upon request.

Ease of Assembly

Harding Series Bench Assembly.

We are the Only National Workbench Manufacturer that Welds the Frame Together and Assembles it to the Top.

1. Place your new workbench on top of a table with the cardboard seam facing up. Open the carton. Do not remove the cardboard yet. If you ordered drawers or CPU holders, assemble them before the legs. (Go to their individual web site pages for instructions if needed. (benchdepot.com)

2. Position the legs. If you have a lot of benches to do, we recommend two man teams. If you have Static Control benches, make certain the wrist strap jack is on the front side of the leg.

3. Insert two screws with lock washers into each leg.

4. Tighten until lock washer is flat. It doesn't have to be tighter than that.

5. You're done. Turn it over. Its easier and safer with two men. Toss out the cardboard.

Warranty

PRINT


	Workbench Warranty BenchPro™ has been producing the nation's strongest, longest lasting ergonomic workbenches since 1987. We are so sure our products will perform properly, we offer the following warranty: BenchPro™ benches, options and accessories are warranted to the original purchaser for 25 - years. This includes every component and every function. Exceptions: Johnson series are warranted for three years. (Electric Lift Activated Adjustable Height Table). Eisenhower series are warranted for ten years. Workbenches used in multiple shift operations shall have the warranty prorated accordingly. Hydraulic bench lift - system components are warranted for ten - years. All lighting products are warranted for ten - years. For Service: Call BenchPro™ at 888-700-9888 or email info@benchpro.com. Customers only have the obligation to report the problem and BenchPro™ will take care of the rest. BenchPro™ will either refund the entire purchase price including freight (if by our freight carrier) and tax (if any) or replace the product or component that is defective at our discretion. Product Returns: As we make all orders from base materials, and do not carry an inventory, we charge a "restocking charge" on unneeded and unwanted, yet ordered products. We also charge a restocking charge for products ordered but cancelled after the product is built. This is to cover our repackaging and handling, and remarketing. Customers pay the cost of freight both ways. Restocking charge schedule: A. Kennedy, Roosevelt Series in standard sizes and colors will be charged 15%. B. Dewey, Harding, Jefferson, Grant and Adams Series in standard sizes and colors will be charged 30% restocking charge. C. Any bench in a custom size or color will be charged a 50% restocking charge, as we will have a difficult time reselling them without a large discount. D. Custom design and non-catalogue items are non-returnable. E. No product shall be returned after 60 days. No return of defective product is ever required. (We ask for an electronic photo in cases where we have not seen the problem before). Freight Damaged Product: USA freight regulations make freight companies’ drivers responsible for checking shipments for damage when they pick up. Our customers are responsible for checking for damage when receiving and signing for a shipment. We state this on our acknowledgment and invoice in case customers are not aware of the procedure. Once the product is in your facility, we assume you mishandled the product. Most carriers give us 5 days after delivery to notify them of damage, and will cover the cost of replacements and the freight. If you have a problem, call or write and we will notify the carrier, then replace the product at no charge to you. From the lawyers: In no case shall BenchPro™, its distributors, employees, related divisions, and other entities be responsible for any direct, consequential or indirect damage caused by the use, inability to use, or incorrect use of our products. Our liability shall be limited to replacement of product or a full refund. Litigation: All claims and/or disputes relating to the sale, quality and/or use of our products are to be settled by binding arbitration in the state of California, county of San Diego or any other location mutually agreeable to both parties. Destruction: Dangerous products should not be put into open waste disposal system until they have been made unserviceable, so no third party can claim them and be injured. (This includes wobbly tables or chairs.)

Recommended Height

What is the best work surface height for me?

You can order your benches at any work surface height without incurring additional cost, or select the lowest height you believe useful and add either our optional adjustable legs, our electric lift system or our crank-up system.

We have seen orders for almost every work surface height. Some Customers want to sit down and work, others want to stand. Here are some thoughts that may be of assistance:

1. Desks are 30" high.

2. Desk chairs usually have a seat cushion height adjustability range of around 17" to 22".

3. Work surfaces should never be more than 9" higher than the top of the chair range. Conclusion: If you need a work surface higher than 31", you will need a taller chair.

4. Taller chairs usually have a foot ring and a wider base. (Adjustable foot rings are critical as employees come in all sizes too.)

5. Our taller chairs have a seat cushion height adjustability range of 22" to 32". (Some brands have ranges of only 5" or 8".)

6. We do not recommend chairs be used at benches with work surfaces of 37" and higher, as some employees will attempt to "climb" the chair, and could be injured when the chair rolls or tips.

All Accessories

All Accessories
	Drawers These fully-welded drawers hold up 100 lbs.
	Shelves Choose from upright-mounted, riser or under-shelves.
	Lights Add fluorescent or LED lights above your workbench.
	Uprights Add shelves lights or accessories above your workbench.
	Power Strips Add UL listed power strips to your workbench.
	Bin Rails Add convenient bin access to your workbench.
	Casters Make your workbench mobile with these non-marring casters.
	Articulating Accessories Choose from Monitor, Bin Box, Document and Tool Holders.
	Footrest Improves Posture, Enhances Circulation, Customizable Height.
	Keyboard Trays Reduce Strain and Maintain Neutral Wrist Posture.
	Cabinets Store Tools and General Items.
	Paper Cutter Designed for Precision Cuts and Durability.

Harding Series Workbench - Extreme Heavy Duty with Stainless Steel Top

Harding Series Bench Assembly.

Workbench Warranty