Roosevelt Series Workbench with 1 3/4" Thick Top Solid Oiled Butcher Block

Skip to the beginning of the images gallery

Factory Assembly Available.
1-3/4" Thick Solid Butcherblock Top.
Steel Reinforced Top.
1200# Capacity.
Butcherblock Grading.
14-gauge Steel.
Adjustable Legs 30" to 36".
Butcherblock Care Instructions.
24 Torch Welds Strong!

Note: Our butcherblock tops are generally treated with oil for industrial assembly applications.

The Solid Butcherblock tops used by BenchPro™ are made from 1-3/4" thick strips of genuine Hardwood. To prevent warpage and splitting, the wood is died in a low-heat atmosphere for almost one year before it is cut into strips and glued edge to edge. The hardwood strips vary in width, so that some strips are single and some strips are double wide. This gives the tops added strength while reducing the possibility of the top splitting along its seams.

Ease of Assembly

Roosevelt Series Bench Assembly.

1. Place the unopened box on a small table with the seam tape facing up. Open the box, leaving the cardboard underneath.
Separate out the interior packaging. (This will save a lot of time)

2. Locate the bag of fasteners (Attached to one screw under the top). Insert one glide through the threaded hole in the bottom of the legs. Put the nut on the end of the inserted glide. No need to tighten now.

3. Find the front side of the legs and top. (Labeled Front). Place the top of the leg frame holes over the elevated screw heads, slide the base so the screw shafts slide into the slot. Tighten the screws.

4. The front of the legs have 1/4” holes. The back side of each leg has 4 smaller, threaded holes. Position the back bar over the threaded holes, insert screws and tighten. (There are no lock washers or nuts required here)

5. Turn it over.

6. See if the table wabbles due to an uneven floor. Lower one glide to stop the wobble. Now tighten the nuts on the glides.

Warranty

PRINT


	Workbench Warranty BenchPro™ has been producing the nation's strongest, longest lasting ergonomic workbenches since 1987. We are so sure our products will perform properly, we offer the following warranty: BenchPro™ benches, options and accessories are warranted to the original purchaser for 25 - years. This includes every component and every function. Exceptions: Johnson series are warranted for three years. (Electric Lift Activated Adjustable Height Table). Eisenhower series are warranted for ten years. Workbenches used in multiple shift operations shall have the warranty prorated accordingly. Hydraulic bench lift - system components are warranted for ten - years. All lighting products are warranted for ten - years. For Service: Call BenchPro™ at 888-700-9888 or email info@benchpro.com. Customers only have the obligation to report the problem and BenchPro™ will take care of the rest. BenchPro™ will either refund the entire purchase price including freight (if by our freight carrier) and tax (if any) or replace the product or component that is defective at our discretion. Product Returns: As we make all orders from base materials, and do not carry an inventory, we charge a "restocking charge" on unneeded and unwanted, yet ordered products. We also charge a restocking charge for products ordered but cancelled after the product is built. This is to cover our repackaging and handling, and remarketing. Customers pay the cost of freight both ways. Restocking charge schedule: A. Kennedy, Roosevelt Series in standard sizes and colors will be charged 15%. B. Dewey, Harding, Jefferson, Grant and Adams Series in standard sizes and colors will be charged 30% restocking charge. C. Any bench in a custom size or color will be charged a 50% restocking charge, as we will have a difficult time reselling them without a large discount. D. Custom design and non-catalogue items are non-returnable. E. No product shall be returned after 60 days. No return of defective product is ever required. (We ask for an electronic photo in cases where we have not seen the problem before). Freight Damaged Product: USA freight regulations make freight companies’ drivers responsible for checking shipments for damage when they pick up. Our customers are responsible for checking for damage when receiving and signing for a shipment. We state this on our acknowledgment and invoice in case customers are not aware of the procedure. Once the product is in your facility, we assume you mishandled the product. Most carriers give us 5 days after delivery to notify them of damage, and will cover the cost of replacements and the freight. If you have a problem, call or write and we will notify the carrier, then replace the product at no charge to you. From the lawyers: In no case shall BenchPro™, its distributors, employees, related divisions, and other entities be responsible for any direct, consequential or indirect damage caused by the use, inability to use, or incorrect use of our products. Our liability shall be limited to replacement of product or a full refund. Litigation: All claims and/or disputes relating to the sale, quality and/or use of our products are to be settled by binding arbitration in the state of California, county of San Diego or any other location mutually agreeable to both parties. Destruction: Dangerous products should not be put into open waste disposal system until they have been made unserviceable, so no third party can claim them and be injured. (This includes wobbly tables or chairs.)

Brand Comparison

10 Units 30" x 60"

^Brand	Warranty	Ship Time	Large Orders	Assembly	Capacity	Colors	Accessories	Price Each	Made In
Global Industrial	1 year	1 to 5 Days	If In Stock	‡60 Minutes	*2,000 lb	Blue, Gray & Black	Limited	$290	China
Uline	1 year	1 to 5 Days	If In Stock	60 Minutes	500 lb	Gray	Very Limited	$370	US
Bench Depot	25 year	5 Days	1 to 3 Weeks	3 Minutes	1,600 lb	Any Color	Complete	$191	Mexico

*Questionable: Previously stated 1,000#, then 2,000#, now 3,000#.

‡View Survey Sample.

Note: Information taken from www.globalindustrial.com, www.uline.com sites and phone calls. If incorrect, please advise.

12/10/2022

Accessories

Accessories
	Drawers These fully-welded drawers hold up 100 lbs.
	Shelves Choose from upright-mounted, riser or under-shelves.
	Lights Add fluorescent or LED lights above your workbench.
	Uprights Add shelves lights or accessories above your workbench.
	Power Strips Add UL listed power strips to your workbench.
	Bin Rails Add convenient bin access to your workbench.
	Casters Make your workbench mobile with these non-marring casters.
	Articulating Accessories Choose from Monitor, Bin Box, Document and Tool Holders.
	Footrest Improves Posture, Enhances Circulation, Customizable Height.
	Keyboard Trays Reduce Strain and Maintain Neutral Wrist Posture.
	Cabinets Store Tools and General Items.

Roosevelt Series Workbench with 1 3/4" Thick Top Solid Oiled Butcher Block

Roosevelt Series Bench Assembly.

Workbench Warranty

Brand Comparison